March's newsletter is out! ✉️

read
Enviroseal
Enviroseal - Image 2

Enviroseal

Price range: $54.00 through $205.00

EnviroSeal™ permanently reacts and converts soluble calcium hydroxide to an insoluble calcium silicate in new and old concrete and masonry surfaces, permanently stopping efflorescence. This reaction strengthens concrete and reduces porosity while increasing density and chemical resistance. Choose EnviroSeal to increase the service life of concrete and masonry-based products.

Description

Features

✅ Permanently seals capillaries in concrete and cementitious substrates

✅ Prevents efflorescence and improves chemical resistance

✅ Strengthens concrete to extend service life

✅ Will not peel, scratch, or wear away like surface sealers

✅ Compatible with polishing for a glossy, high-sheen finish

✅ Environmentally friendly, inorganic, and water-soluble formulation

Additional information

Weight N/A
Dimensions N/A
Sizes

1 Gal, 4×1 Gal, 5 Gal Pail

Compatibility

To gap fill, seal, damp proof and prevent mold, seal masonry and concrete surfaces with MasonryGuard.

To weatherproof concrete and masonry surfaces, seal with X4.

Compatible with:
✅ Enviroguard Cleaners & Stain Removers
✅ Dutrion Tablets & Powders
✅ Enviroguard Equipment
✅ FOAMiT Equipment
✅ Premira Equipment
✅ Titan Tool Equipment

Instructions

  • EnviroSeal is ready to use. Do not dilute. Shake or mix prior to opening
  • Air and surface temperatures must be above freezing during application and for three days after. Do not apply to hot surfaces in direct sunlight or in strong wind. Avoid rain for 24 hours after application.
  • Dampen surface(s) with water prior to application, leaving no puddles or dry spots. For those both cleaning and sealing on the same day, the rinse step following cleaning will make re-dampening the surface unnecessary.
  • Apply EnviroSeal in two to four “wet-on-wet” applications 30 to 45 minutes apart. (After 30-45 minutes of spraying, return to the original starting point and apply the subsequent applications while the surface is still damp.)
  • Apply EnviroSeal to the point of complete saturation (as run-off occurs), adding more sealer to faster-absorbing areas. Do not over-apply or leave puddles.
  • Broom or roll out puddles or excess run-off. Puddles will leave a hard glassy or white film on the surface, which is not paintable and is difficult to remove.

Application

Use a low-pressure sprayer (50 psi or below), equipped with fan-tip nozzle such as a manual pump sprayer or electric sprayer. A paint roller may be used if/when spray application is not an option.

Coverage

  • Poured Concrete 2 applications 200 sq ft per gallon
  • Concrete Block 3 applications 100 sq ft per gallon
  • Cinder Block, Sand Stone, Grout or Similarly Porous Surfaces 4 applications 80 sq ft per gallon

Drying & Curing

The surface should be dry to the touch (and appear dry) within 1 to 3 hours. Ventilate the area to facilitate drying and curing. As EnviroSeal reacts and expands inside the concrete pores, it will purge any dirt, mineral deposits, or efflorescence to the surface. This is common in older concrete, and may last for several days. Purged material may be swept or washed off. Full cure will be reached in 60-90 days after application.

Storage

Store in a cool, dry place out of direct sunlight at temperatures below 100F. Protect from freezing. If the sealer freezes, thaw and mix thoroughly before use.

Cleanup

Flush equipment with warm water immediately after use. Wipe off drips and over spray while still wet. Removing dried residue from the surface may require mechanical abrasion. In 2 to 3 hours after application, rinse the treated surface with water and scrub with a stiff bristle brush to remove any surface residue.

Documentation

EnviroSeal_SDS
EnviroSeal TDS
PPE Selection Guide
Label (watermark)
EnviroSeal Fundamentals Guide

Reviews

There are no reviews yet.

Be the first to review “Enviroseal”

Your email address will not be published. Required fields are marked *

Purchased Together

You May Also Like

Related products