S3: Drainage, Inspection & Maintenance
Stage three of our waterproofing prep system. Getting the water away from a wall you just finished, what to check a year out, and the point where the job stops being yours.
Efflorescence comes back when water keeps showing up. The wall itself is finished by this point, so most of what is left is a conversation with the customer about where that water is coming from, and a date to come back and look at it.
Why It Comes Back
What the Treatment Does Not Cover
Water works into the masonry, picks up salts on the way through, and carries them out to a face where it can dry off, leaving the salt sitting on the surface. Stage 1 took that deposit off and Stage 2 converted what was still in the wall, which is as far as treating the wall itself goes.
What neither stage touches is how much water turns up in the first place. That comes down to grade, roof drainage and window wells, none of which are on the wall you just worked on. Densify a wall and leave a downspout dumping next to it and you will be looking at that wall again.
The Water
Where It Is Coming From
None of this is waterproofing. It is drainage, it is usually the cheapest work on the property, and the owner can handle most of it without calling anybody back out. Walk all three with them before you load the truck.
| Check this | What it should be | Why it matters |
|---|---|---|
| Grade | Falls away from the foundation, about 6 inches over the first 10 feet. | Water that pools against a wall soaks into it. Flat or reversed grade holds it there long enough to do that. |
| Downspouts | Discharge extended at least 6 feet out from the wall. | One downspout drops a whole roof plane at the base of the wall. Roof water concentrated at the perimeter is one of the most common causes of hydrostatic seepage. |
| Window wells | A drain in every well, and one that actually runs. | A well with no drain fills in a hard rain and pushes water through the window frame and the wall above it, which is above the zone you treated. |
The Schedule
What to Put on the Calendar
Write it down before you leave, because nobody remembers any of this a year out.
Once a year somebody looks at the wall for new efflorescence, surface cracking, and anything lifting or peeling off the masonry. Catching it early usually keeps the fix local instead of going back over the whole wall. On a System 3 job the treated face is backfilled, so the annual look covers the inside of the wall, whatever is above grade, and the drainage.
Reapplying EnviroSeal depends entirely on what went over the wall.
| What is over the wall | Does EnviroSeal come back? | What you maintain |
|---|---|---|
| Nothing, masonry left exposed | Yes, on a cycle set by substrate and exposure. | The densified surface itself. |
| MasonryGuard, or a Phoenix interior membrane | No. It is sealed under the coating. | The coating, on its own system schedule. |
| Phoenix exterior, System 3 | No. The face is backfilled. | Whatever is visible inside and above grade. |
Scope
When It Is Not an Efflorescence Job
What we cover here is surface efflorescence and preventive densification. Some walls are past that, and the sooner you call it the better.
| What you find | What it tells you | Where it goes |
|---|---|---|
| Active seepage, or water at the cove joint | Water is being pushed in under pressure, not drawn through the masonry. | Full moisture assessment, most likely a waterproofing system. Densifying does not relieve pressure. |
| Standing water | A drainage or groundwater problem that no surface treatment covers. | Full moisture assessment before you quote any more surface work. |
| Cracking | Possible movement, and an open path for water regardless of how the rest of the wall was treated. | Assessment, and an engineer first if there is any sign of movement. |
| Bowing | Structural movement. Not a surface condition at all. | Stop. Licensed structural engineer, or a qualified foundation repair specialist. |
Get the referral in writing and quote nothing further until it comes back. Assessing structural conditions is outside what this service is scoped to do, and documenting the handoff keeps the record clear on what you were and were not hired for.
The Handoff
What to Tell the Customer
All of it happens after you drive away, so leave it in writing.
Three Fixes and a Date
The Product
Where EnviroSeal Comes Back
Before you quote a reapplication, check what is on the wall.
EnviroSeal
A penetrating silicate densifier. It permanently converts soluble calcium hydroxide in new and old concrete and masonry into insoluble calcium silicate, which strengthens the substrate and stops efflorescence at the same time.
- Comes back on: bare masonry with nothing coated over it, on an interval set by substrate and exposure.
- Does not come back on: walls under MasonryGuard or a Phoenix membrane, or any backfilled System 3 face.
- Coverage: depends on the substrate. Roughly 200 to 250 sq ft per gallon on dense poured concrete, and 80 to 120 on CMU.
- Application: brush, roller, squeegee or low pressure sprayer, per the data sheet.
- Sizes: 1 gallon jugs, 4 gallon cases, 5 gallon pails. Made in USA.
When Drainage Is Not Enough, Waterproof It
We build four pressure rated systems on one proven preparation sequence, from minor vapor control to 250+ PSI hydrostatic head. The moment a wall crosses out of surface work, this is where it goes.